top of page
RoofHelp! | Coatings Logo

Roof Coating Basics: What San Antonio Property Owners Should Know Before They Decide

Nov 4
7 min read
Aerial view of a large warehouse with white and tan roofs, HVAC units, and a distant city skyline under a bright blue sky.

Most people don't look into roof coatings until something prompts it. Maybe a ceiling tile stained after a spring storm, or a contractor used the word "restoration" during a walkthrough, or the top floor of the building has been running warm all summer. Then you're trying to make a decision about a roof you've probably never stood on.


Below is a straightforward rundown of what a coating is, what it does, which roofs can take one, and when it's worth the money. It's written with San Antonio buildings in mind, since our mix of long summers, strong UV, and sudden heavy rain shapes most of these decisions.


What a Roof Coating Actually Is

A roof coating is a liquid product that's applied over your existing roof and cures into a flexible, rubber-like membrane. When it's done, the roof surface has no seams, laps, or exposed fasteners. On a low-slope roof, those seams and fasteners are usually where leaks begin, so covering them with one continuous layer solves a lot.


People sometimes call it roof paint. The two aren't really comparable. House paint goes on a few thousandths of an inch thick. A commercial coating system is applied to a set thickness, often 20 to 30 dry mils or more, and is made to stretch as the roof moves and keep water out for years. Most systems also add polyester fabric at seams, flashings, and drains, so the spots that leak most often get extra material.


What a Coating Does for Your Roof

When it's applied correctly, a coating handles several jobs:

  • Waterproofing: Seams, fastener heads, small cracks, and penetrations all end up under one surface.

  • UV protection: The coating absorbs the sun damage that would otherwise dry out and crack the roof below it.

  • Heat reduction: White and light-colored coatings reflect a large share of sunlight, so the roof and the rooms under it stay cooler.

  • Less thermal movement: A roof that heats up less each afternoon expands and contracts less, which puts less strain on seams and flashings.

  • Longer service life: The existing roof stays in place, so you get added years without paying for a tear-off.


The Main Types of Roof Coatings

You'll hear "elastomeric" a lot. It just means the coating can stretch and return to shape. It's a broad category, and both of the coatings below fall inside it. These two make up most of the work we see on commercial and residential roofs in Central Texas.


Acrylic Roof Coatings

Acrylics are water-based, very reflective, and generally the more budget-friendly option. They do well on roofs that drain, such as most metal roofs and low-slope roofs with decent pitch. Where they struggle is standing water. If a section of roof holds water for a day or two after a storm, acrylic in that area tends to soften and wear out early.


Silicone Roof Coatings

Silicone holds up much better under ponding water and doesn't break down much in UV. That's why it's often used on flat roofs that have a few low spots. A couple of downsides to know about: it picks up dirt, which dulls its reflectivity over time, and very few products will bond to it later. Once a roof has silicone, future recoats are usually silicone too.


Which one fits depends on the roof type, how well it drains, and how long you plan to own the building. Click here to learn more about choosing between silicone and acrylic roof coatings.


Which Roofs Are Good Candidates

Coatings can go over many existing roof systems, including:

  • Metal roofs with surface rust, loose fasteners, or leaking seams

  • EPDM and other single-ply membranes that are aging but still well attached

  • Modified bitumen and built-up roofs that are weathered but structurally sound

  • Spray foam roofs that need a new protective topcoat


The bigger question is what's underneath. A coating seals the surface and that's all it does. It won't dry out wet insulation, fix a soft or rotted deck, or hold down a membrane that's coming loose. If water has worked its way into the roof assembly and you coat over it, the moisture stays in there and keeps doing damage.


This is why every coating job should start with an inspection. A good one checks the surface, seams, and flashings, and usually includes moisture testing, since saturated insulation often can't be seen from the top of the roof. A few wet areas can be cut out and replaced before coating. If the readings show moisture across large parts of the roof, coating probably isn't the right fix.


What a Professional Coating Project Looks Like

It helps to know the steps so you can read a proposal and see what's included.


Most jobs go in roughly this order:

  1. Inspection and moisture survey to confirm the roof qualifies and mark any trouble areas.

  2. Cleaning, usually pressure washing, to get rid of dirt, chalky residue, and loose material so the coating bonds.

  3. Repairs to flashings, open seams, blisters, and any wet insulation.

  4. Primer, if the surface needs it. Rusted metal and some older membranes need primer for good adhesion. Plenty of roofs don't.

  5. Reinforcement with fabric and mastic at seams, penetrations, and transitions.

  6. Coating application in one or more coats until the specified thickness is reached.

  7. Final walkthrough to check thickness, coverage, and detail work.


If a proposal doesn't mention cleaning or doesn't list a coating thickness, ask about it. Poor surface prep and coatings applied too thin are two of the most common reasons coatings fail early.


Reflective Coatings in San Antonio Heat

Sunlit rooftop with white reflective membrane, HVAC units, and distant city skyline under a clear blue sky.

A dark roof in San Antonio in July gets hot enough to burn your hand. Much of that heat moves down into the building, and the air conditioning keeps working to remove it well into the evening.


A reflective coating cuts down how much heat the roof takes on in the first place. Highly reflective roof materials can stay around 50 to 60 degrees cooler than standard surfaces during peak summer, and cool roof guidance for Central Texas buildings suggests choosing low-slope coatings with at least 65 percent solar reflectance and high thermal emittance.


Buildings with big flat roofs and not much insulation usually see the most benefit. Warehouses, retail centers, and older office buildings are good examples, and top-floor tenants are often the first to notice. How much you save depends on your insulation, what color the roof was before, and how clean the coating stays.


Common Misunderstandings About Roof Coatings

These come up a lot in conversations with property owners.

  • "Coatings let the roof breathe." Acrylics let a little water vapor pass through, and silicone lets through less. Neither will remove moisture that's already trapped in the roof. That has to be handled during repairs.

  • "A coating makes the roof fireproof." Some coating systems have fire ratings, but the rating applies to the specific roof assembly that was tested. If your insurer or local code cares about fire performance, ask for the rating on the exact system being proposed.

  • "Coatings prevent mold and algae." Many coatings contain mildew-resistant additives, and a roof that drains and dries quickly is less likely to grow anything. A roof that holds water and collects leaves will still need cleaning.

  • "Any roof can be coated." Coatings are best for roofs that are aging but still sound. A roof that has already failed needs more than a coating.


How Long Coatings Last and How to Maintain Them

Depending on the coating type and how thick it's applied, a quality system usually protects a roof for 10 to 20 years. Thicker applications tend to last longer and often come with longer warranties.

Upkeep is not complicated:

  • Inspect twice a year, once after spring storm season and again before winter.

  • Check after hail or strong winds, which hit the San Antonio, New Braunfels, and Austin area fairly often.

  • Keep drains and scuppers clear so water runs off instead of sitting.

  • Clean the surface now and then, especially silicone, to keep it reflective.

  • Recoat when wear shows up. A recoat costs much less than replacing the roof and starts another round of protection.


When to Coat

The right time to coat is while the roof still has a good amount of life in it. Prep is lighter, repairs are small, and you're sealing a roof that's in decent shape. If you wait until it leaks in several places and the insulation is soaked, the repair list grows, and at some point the numbers stop working in coating's favor.

As a rough guide, a roof that's 10 to 15 years old with some seam wear or surface cracking, but no widespread leaking, is usually right in the range where a coating makes the most sense.


Frequently Asked Questions

How much does a roof coating cost compared to a new roof? 

Usually a fraction of the cost, since there's no tear-off or disposal and much less labor. The final number depends on the roof's size and condition, how much repair is needed, and which coating system is used.

Yes, as long as the source of the leak is found and repaired before the coating goes on. Coating over a leak without fixing the cause rarely holds.

Most commercial jobs take anywhere from a few days to a couple of weeks, depending on size, repairs, and weather. Businesses can usually keep operating while the work is done.

Silicone is usually the better choice for flat roofs that hold water. Acrylic works well on roofs that drain, including most metal roofs. An inspection will tell you which suits your roof.

For most buildings with low-slope roofs in South Texas, yes. The savings are biggest on buildings with large roofs and limited insulation.


Conclusion

A coating can protect an aging roof, reduce heat coming into the building, and push back the cost of a replacement, provided the roof under it is still in good shape. Knowing how coatings work makes it easier to ask the right questions and compare quotes. If you want to know whether your roof is a good candidate, RoofHelp! | Coatings provides inspections, assessments, and coating systems suited to San Antonio's climate. Schedule a roof assessment to get a clear picture of where your roof stands.


Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
RoofHelp! | Coatings Logo
bottom of page